from small one page howto to huge articles all in one place

search text in:

Which screen resolution do you use?

poll results

Last additions:
using iotop to find disk usage hogs

using iotop to find disk usage hogs






average rating: 1.7 (102 votes) (1=very good 6=terrible)

May 25th. 2007:




why adblockers are bad

Workaround and fixes for the current Core Dump Handling vulnerability affected kernels

Workaround and fixes for the current Core Dump Handling vulnerability affected kernels






average rating: 1.4 (42 votes) (1=very good 6=terrible)

April, 26th. 2006:

You are here: manpages


Section: System Administration (8)
Updated: October 2011
Index Return to Main Contents


readprofile - read kernel profiling information  


readprofile [options]  


This manpage documents version 2.0 of the program.  


The readprofile command uses the /proc/profile information to print ascii data on standard output. The output is organized in three columns: the first is the number of clock ticks, the second is the name of the C function in the kernel where those many ticks occurred, and the third is the normalized `load' of the procedure, calculated as a ratio between the number of ticks and the length of the procedure. The output is filled with blanks to ease readability.  


-a, --all
Print all symbols in the mapfile. By default the procedures with reported ticks are not printed.
-b, --histbin
Print individual histogram-bin counts.
-i, --info
Info. This makes readprofile only print the profiling step used by the kernel. The profiling step is the resolution of the profiling buffer, and is chosen during kernel configuration (through `make config'), or in the kernel's command line. If the -t (terse) switch is used together with -i only the decimal number is printed.
-m, --mapfile mapfile
Specify a mapfile, which by default is /usr/src/linux/ You should specify the map file on cmdline if your current kernel isn't the last one you compiled, or if you keep elsewhere. If the name of the map file ends with `.gz' it is decompressed on the fly.
-M, --multiplier multiplier
On some architectures it is possible to alter the frequency at which the kernel delivers profiling interrupts to each CPU. This option allows you to set the frequency, as a multiplier of the system clock frequency, HZ. This is supported on i386-SMP (2.2 and 2.4 kernel) and also on sparc-SMP and sparc64-SMP (2.4 kernel). This option also resets the profiling buffer, and requires superuser privileges.
-p, --profile pro-file
Specify a different profiling buffer, which by default is /proc/profile. Using a different pro-file is useful if you want to `freeze' the kernel profiling at some time and read it later. The /proc/profile file can be copied using `cat' or `cp'. There is no more support for compressed profile buffers, like in readprofile-1.1, because the program needs to know the size of the buffer in advance.
-r, --reset
Reset the profiling buffer. This can only be invoked by root, because /proc/profile is readable by everybody but writable only by the superuser. However, you can make readprofile set-user-ID 0, in order to reset the buffer without gaining privileges.
-s, --counters
Print individual counters within functions.
-v, --verbose
Verbose. The output is organized in four columns and filled with blanks. The first column is the RAM address of a kernel function, the second is the name of the function, the third is the number of clock ticks and the last is the normalized load.
-V, --version
Display version information and exit.
-h, --help
Display help text and exit.


Browse the profiling buffer ordering by clock ticks:
   readprofile | sort -nr | less

Print the 20 most loaded procedures:
   readprofile | sort -nr +2 | head -20

Print only filesystem profile:
   readprofile | grep _ext2

Look at all the kernel information, with ram addresses:
   readprofile -av | less

Browse a `freezed' profile buffer for a non current kernel:
   readprofile -p ~/profile.freeze -m /

Request profiling at 2kHz per CPU, and reset the profiling buffer:
   sudo readprofile -M 20


readprofile only works with an 1.3.x or newer kernel, because /proc/profile changed in the step from 1.2 to 1.3

This program only works with ELF kernels. The change for a.out kernels is trivial, and left as an exercise to the a.out user.

To enable profiling, the kernel must be rebooted, because no profiling module is available, and it wouldn't be easy to build. To enable profiling, you can specify "profile=2" (or another number) on the kernel commandline. The number you specify is the two-exponent used as profiling step.

Profiling is disabled when interrupts are inhibited. This means that many profiling ticks happen when interrupts are re-enabled. Watch out for misleading information.  


/proc/profile              A binary snapshot of the profiling buffer.
/usr/src/linux/  The symbol table for the kernel.
/usr/src/linux/*           The program being profiled :-)


The readprofile command is part of the util-linux package and is available from Linux Kernel Archive




Support us on Content Nation
rdf newsfeed | rss newsfeed | Atom newsfeed
- Powered by LeopardCMS - Running on Gentoo -
Copyright 2004-2020 Sascha Nitsch Unternehmensberatung GmbH
Valid XHTML1.1 : Valid CSS : buttonmaker
- Level Triple-A Conformance to Web Content Accessibility Guidelines 1.0 -
- Copyright and legal notices -
Time to create this page: 14.4 ms