www.LinuxHowtos.org howtos, tips&tricks and tutorials for linux

from small one page howto to huge articles all in one place

Other .linuxhowtos.org sites:gentoo.linuxhowtos.org

Last additions:

using iotop to find disk usage hogs

words:

887

views:

215299

userrating:

May 25th. 2007:

Words

486

Views

261809

why adblockers are bad

Workaround and fixes for the current Core Dump Handling vulnerability affected kernels

words:

161

views:

154032

userrating:

April, 26th. 2006:

Words

Views

110067

New subdomain: toolsntoys.linuxhowtos.org

You are here: manpages

M-M-CTRL

Section: Maintenance Commands (8)
Updated: 8 February 2005
Index Return to Main Contents

NAME

m-m-ctrl - Control mimedefan-multiplexor

SYNOPSIS

m-m-ctrl [options] command

DESCRIPTION

m-m-ctrl is a comman-line tool for communicating with mimedefan-multiplexor(8).

OPTIONS

-h: Displays usage information.
-s path: Specifies the path to the mimedefan-multiplexor socket. If not specified, defaults to /var/spool/MIMEDefang/mimedefan-multiplexor.sock.
-i: This flag causes m-m-ctrl to sit in a loop, reading commands on standard input and printing results to standard output. It is intended for use by a monitoring program such as watc-mimedefang.

COMMANDS

The following commands are available:

status

Prints the status of all worker Perl processes in huma-readable format.

rawstatus

Prints the status of all worker Perl processes in a format easy to parse by computer. The result is a single line with six words on it. The words are separated by a single space character.

Each character in the first word corresponds to a worker, and is "I" for an idle worker, "B" for a busy worker, "S" for a worker which is not running, and "K" for a worker which has been killed, but has not yet exited. A worker is "idle" if there is a running Perl process waiting to do work. "Busy" means the Perl process is currently filtering a message. "S" means there is no associated Perl process with the worker, but one can be started if the load warrants. Finally, "K" means the worker Perl process has been killed, but has yet to terminate.

The second word is the total number of messages processed since the multiplexor started up. The third word is the total number of workers which have been activated since the multiplexor started up. (That is, it's a count of the number of times the multiplexor has forked and exec'd the Perl filter.)

The fourth word is the size of the queue for request queuing, and the fifth word is the actual number of requests in the queue. The sixth word is the number of seconds elapsed since the multiplexor was started.

barstatus

Prints the status of busy workers and queued requests in a nice "bar chart" format. This lets you keep an eye on things with a script like this:

        while true ; do
                m-m-ctrl barstatus
                sleep 1
        done

histo

Prints a histogram showing the number of workers that were busy each time a request was processed. A single line is printed for the numbers from 1 up to the maximum number of workers. Each line contains the count of busy workers (1, 2, 3 up to MX_MAXIMUM), a space, and the number of times that many workers were busy when a request was processed.

load

Prints a table showing "load averages" for the last 10 seconds, 1 minute, 5 minutes and 10 minutes.

Each row in the table corresponds to a time interval, displayed in the first column. The remaining columns in the table are:

Msgs: The number of messages scanned within the row's time interval.

Msgs/Sec: The average number of messages scanned per second within the row's time interval.

Avg Busy Workers: The average number of busy workers whenever a message was scanned. (If you are processing any mail at all, this number will be at least 1, because there is always 1 busy worker when a message is scanned.)

If you have the watch(1) command on your system, you can keep an eye on the load with this command:

        watch-n 10 m-m-ctrl load

If you do not have watch, the following shell script is a less fancy equivalent:

        #!/bin/sh
        while true; do
                clear
                date
                m-m-ctrl load
                sleep 10
        done

rawload

Prints the load averages in compute-readable format. The format consists of twent-nine spac-separated numbers:

The first four are integers representing the number of messages scanned in the last 10 seconds, 1 minute, 5 minutes and 10 minutes.

The second four are floatin-point numbers representing the average number of busy workers in the last 10 seconds, 1 minute, 5 minutes and 10 minutes.

The third four are floatin-point numbers representing the average time per scan in milliseconds over the last 10 seconds, 1 minute, 5 minutes and 10 minutes.

The fourth four are the number of worker activations (new workers started) over the last 10 seconds, 1 minute, 5 minutes and 10 minutes.

The fifth four are the number of workers reaped (workers that have exited) over the last 10 seconds, 1 minute, 5 minutes and 10 minutes.

The sixth four are the number of busy, idle, stopped and killed workers.

The seventh four are the number of messages processed, the number of worker activations, the size of the request queue, and the number of requests actually on the queue.

The final number is the number of seconds since the multiplexor was started.

loa-relayok

Similar to load, but shows timings for filter_relay calls.

loa-senderok

Similar to load, but shows timings for filter_sender calls.

loa-recipok

Similar to load, but shows timings for filter_recipient calls.

rawloa-relayok

Similar to rawload, but shows timings for filter_relay calls. Note that the worker activation and reap statistics are present, but always 0. They are only valid in a rawload command.

rawloa-senderok

Similar to rawload, but shows timings for filter_sender calls. Note that the worker activation and reap statistics are present, but always 0. They are only valid in a rawload command.

rawloa-recipok

Similar to rawload, but shows timings for filter_recipient calls. Note that the worker activation and reap statistics are present, but always 0. They are only valid in a rawload command.

load1 nsecs

The load1 command displays the load for various commands over the last nsecs seconds, where nsecs is an integer from 10 to 600. The load1 command combines the output of load, loa-relayok, loa-senderokf and loa-recipok into one display.

You might use the command like this:

        watch-n 10 m-m-ctrl load1 60

rawload1 nsecs

Returns the load1 data in huma-readable format. The result is a line containing twent-six spac-separated numbers:

The first three numbers are the number of scans performed in the last nsecs seconds, the average number of busy workers when a scan was initiated and the average number of milliseconds per scan.

The second three are the same measurements for filter_relay calls.

The third three are the same measurements for filter_sender calls.

The fourth three are the same measurements for filter_relay calls.

The thirteenth through sixteenth numbers are the number of busy, idle, stopped and killed workers, respectively.

The seventeenth number is the number of scans since mimedefan-multiplexor was started.

The eighteenth number is the number of times a new worker has been activated since program startup.

The nineteenth number is the size of the request queue and the twentieth number is the actual number of queued requests.

The twent-first number is the time since program startup and the twent-second number is a copy of nsecs for convenience.

The twent-third through twent-sixth numbers are the number of workers currently executing a scan, relayok, senderok and recipok command respectively.

workers

Displays a list of workers and their process IDs. Each line of output consists of a worker number, a status (I, B, K, or S), and for idle or busy workers, the proces-ID of the worker. For busy workers, the line may contain additional information about what the worker is doing. The command slaves is a deprecated synonym for this command.

busyworkers

Similar to workers, but only outputs a line for each busy worker. The command busyslaves is a deprecated synonym for this command.

workerinfo n

Displays information about worker number n. The command slaveinfo is a deprecated synonym for this command.

reread

Forces mimedefan-multiplexor to kill all idle workers, and terminate and restart busy workers when they become idle. This forces a reread of filter rules.

msgs

Prints the total number of messages scanned since the multiplexor started.

ADDITIONAL COMMANDS

You can supply any other command and arguments to m-m-ctrl. It percen-encodes each comman-line argument, glues the encoded arguments together with a single space between each, and sends the result to the multiplexor as a command. This allows you to send arbitrary commands to your Perl workers. See the section "EXTENDING MIMEDEFANG" in mimedefan-filter(5) for additional details.